There is water sitting in the bottom. What should I do first?

Switch the dishwasher off at the breaker, then lift out and rinse the filter assembly under the tap - on the current designs it twists out by hand and blocked filters cause more standing water than any failed part. If water still sits there afterwards, the drain pump, the drain hose or the sink connection needs a proper diagnosis. Do not reach into the sump area while the machine has power.

A little water always stays in the sump. Is that a fault?

No. A small amount of water in the sump area is by design on most models - it keeps seals from drying out between cycles. What is not normal is standing water above the base of the tub, or water that has clearly not moved since the last cycle.

Why are the dishes still wet at the end?

Condensation drying, which most current models use, relies on a genuinely hot final rinse and on plastics that do not hold water in their rims. Check that rinse aid is topped up, that the hot tap runs hot at the sink before you start, and that items are not nested. If the final rinse is not reaching temperature, the heating circuit or its sensor needs testing.

It smells even after running. Why?

Almost always residue: the filter, the spray arm holes, the door edge and the gasket fold all collect food debris that no cycle reaches. Clean those by hand, then run a hot cycle empty. A smell that survives that, or comes with slow draining, points at the drain hose or the sink connection instead.

Maytag Dishwasher Repair | Same-Day Service

The work on a Maytag dishwasher follows the water. On the way in: the inlet valve, the float and its switch, the fill logic on the control. On the way out: the filter, the sump, the drain pump, the check valve and the hose run up to the sink or disposer connection. In between: the circulation pump, the diverter, the spray arms and the heating circuit that decides whether a load comes out clean and dry or merely wet.

We isolate the machine at the breaker and shut the supply before anything comes apart, then test rather than guess – because a blocked filter, a kinked hose and a failed pump all present as standing water, and only one of those is a paid repair. You get told which one it is, in plain terms, along with the price, before anything is replaced.

Common Dishwasher Problems

Standing water left in the base at the end of a cycle

Dishes coming out gritty or still soiled

Loads finishing wet when the drying option was selected

Water escaping past the door and onto the floor

Cycle stopping early, or refusing to start at all

Grinding or buzzing during what should be the wash

Dishwasher Error Codes

Recognize a code on your display? Look it up before you unplug anything or attempt a repair.

Why Trust Us With Your Maytag Dishwasher

Measured, Not Guessed | The suspect dishwasher component goes on a meter and is shown to have failed before we recommend replacing it.
Common dishwasher Parts Aboard | The parts that fail most often travel with the technician; anything rarer is ordered on the spot and the return visit booked before we leave.
Isolated Before Anything Opens | The supply to your dishwasher - power, water or gas - is shut off and proven dead before a panel moves, and high-voltage and sealed-system circuits stay with the technician.
Coverage Checked First | Where your dishwasher looks like it may still sit inside manufacturer coverage we flag it before quoting, because work by anyone other than an authorized technician can put that coverage at risk.

Dishwasher Repair, Done Right the First Time

Book Dishwasher Repair

Common Dishwasher Problems

Dishwasher Error Codes

F6E1

F6E3

F6E4

F7E2

F8E2

F8E4

F8E5

F9E1

F9E2

F1E1

FAE4 or F10E4

F1E2

Popular Maytag Dishwasher Models

Maytag MDB7749SAW Built-In Dishwasher

Maytag MDB4030 Series Built-In Dishwasher

Maytag MDB8949SBB Built-In Dishwasher

Maytag MDB4630AWW Built-In Dishwasher

Maytag MDB4651AWW Built-In Dishwasher

Maytag MDB7600AWW Built-In Dishwasher

Why Trust Us With Your Maytag Dishwasher

Dishwasher Repair FAQ